GAUSS-50600 -- GAUSS-50699
GAUSS-50600: “The IP address cannot be pinged, which is caused by network faults.”
SQLSTATE: None
Description: Failed to ping the IP address.
Solution: Change the network settings so that the IP address can be pinged.
GAUSS-50601: “The port [%s] is occupied.”
SQLSTATE: None
Description: The port is occupied.
Solution: Check whether the resources that occupy the port number are available. If the resources are idle, release the port number. Specify other port numbers.
GAUSS-50602: “Failed to bind network adapters.”
SQLSTATE: None
Description: Failed to bind the NIC.
Solution:Contact technical support.
GAUSS-50603: “The IP address is invalid.”
SQLSTATE: None
Description: The IP address is invalid.
Solution: Correct the IP address.
GAUSS-50604: “Failed to obtain network interface card of backIp(%s).”
SQLSTATE: None
Description: Failed to obtain the NIC.
Solution: Check whether the network is normal. Check whether the NIC is normal.
GAUSS-50605: “Failed to obtain back IP subnet mask.”
SQLSTATE: None
Description: Failed to obtain the subnet mask.
Solution: Check whether the network is normal.
GAUSS-50606: “Back IP(s) do not have the same subnet mask.”
SQLSTATE: None
Description: The backIp cannot have the same subnet mask.
Solution: Set a subnet mask to the backIp.
GAUSS-50607: “Failed to obtain configuring virtual IP line number position of network startup file.”
SQLSTATE: None
Description: Failed to obtain the virtual IP address in the NIC startup file.
Solution: Manually check the NIC configuration file to see whether the file is damaged.
GAUSS-50608: “Failed to writing virtual IP setting cmds into init file.”
SQLSTATE: None
Description: Failed to write the virtual IP configuration command in the initialization file.
Solution: Manually check the NIC configuration file to see whether the file is damaged.
GAUSS-50609: “Failed to check port: %s.”
SQLSTATE: None
Description: Failed to check the port.
Solution: Ensure that the port is enabled and not occupied.
GAUSS-50610: “Failed to get the range of random port.”
SQLSTATE: None
Description: Failed to obtain the port range.
Solution: Check the cause of the failure and obtain the range again.
GAUSS-50611: “Failed to obtain network card bonding information.”
SQLSTATE: None
Description: Failed to obtain the NIC binding information.
Solution: Check whether the **/proc/net/bonding/**NIC__ __ID file exists, whether the BONDING_OPTS (the Red Hat environment) or BONDING_MODULE_OPTS (the CentOS environment) strings exist.
GAUSS-50612: “Failed to obtain network card %s value.”
SQLSTATE: None
Description: Failed to obtain the value of the NIC RTU/RX.
Solution: Check whether the network is normal and whether the NIC is normal.
GAUSS-50613: “Failed to set network card %s value.”
SQLSTATE: None
Description: Failed to set the NIC information.
Solution: Check whether the network is normal and whether the NIC is normal.
GAUSS-50614: “Failed to check network information.”
SQLSTATE: None
Description: Failed to check the NIC information.
Solution: Check whether ifconfig is available. If it is, query it again.
GAUSS-50615: “IP %s and IP %s are not in the same network segment.”
SQLSTATE: None
Description: The network segments of the two IP addresses are different.
Solution: Set the network segments of the two IP addresses to the same network segment. Then, perform the operation again.
GAUSS-50616: “Failed to get network interface.”
SQLSTATE: None
Description: Failed to obtain the network interface.
Solution: Ensure that the IP address exists, ifconfig is available, and IP information exists in the NIC configuration file. Then, perform the operation again.
GAUSS-50617: “The node of XML configure file has the same virtual IP.”
SQLSTATE: None
Description:Internal system error.
Solution:Contact technical support.